Hand Tools

The coning tool uses a precision collet to maintain concentricity between the tube and the cutter blades. This unique feature makes it ideal for machining a cone at the end of a tube, or for re-dressing an existing, damaged cone connection. The threading tool is designed to permit on-site end preparation for medium and high pressure tubing installation from 1/4" to 1" O.D. The manual threading tool uses an adjustable split die and a precision guide bushing to cut a perfect thread.

Find a Sales Rep Seal Kit Selector Pump & Compressor Selector


Tube OD	Series	Coning Tool	Threading Tool
1/4"	20,000 PSI	20HCT4	THT4-H
3/8"	20,000 PSI	20HCT6	THT6-H
9/16"	20,000 PSI	20HCT9	THT9-H
3/4"	20,000 PSI	20HCT12	THT12-H
1"	20,000 PSI	20HCT16	THT16-H
1/4"	60,000 PSI	60HCT4	THT4-H
3/8"	60,000 PSI	60HCT6	THT6-H
9/16"	60,000 PSI	60HCT9	THT9-H
3/4"	60,000 PSI	60HCT12	THT12-H
1"	30,000 PSI	30HCT16	THT16-H

Model	Min Inlet	Max Inlet	Max Outlet	Rec Max CR	CPM
QGD-150	75	1100	1100	5:1	20
QGD-90	75	3500	3500	5:1	32
QGD-63	75	6600	6000	5:1	32
QGt-150/90	75	280	3500	25:1	26
QGT-150/63	75	280	6000	25:1	26
QGT-90/63	75	1500	6000	25:1	32

Place the body of the hand coning tool in a suitable vise. The crank handle end of the tool should be elevated slightly so that the lubricant can flow down the lubrication channel to the cutter head. Be sure to provide adequate clearance for the rotation of the crank handle.
Fully retract the cutter blades past the access window by turning the knurled nut counter-clockwise.
Loosen the gland at the front of the tool and insert the tube. The end of the tube should be even with the front of the access window (nearest the cutter blade), but should not contact the cutter blade.
Tighten the gland holding the tube.
Apply a liberal amount of lubricant to the exposed end of the tube, the cutter blades, and through the lubrication channel at the crank handle. Important: Apply lubricant frequently and liberally throughout the cutting operation.
Turn the knurled nut clockwise to gently touch the cutter blade to the tube, then back the knurled nut off 1/4 turn.
Crank the handle clockwise to spin the cutter blades. Turn the knurled nut clockwise to engage and to begin cutting the tube. For best results, establish a gentle but constant feed of the knurled nut and a smooth continuous cutter rotation. Do not try to remove too much material at once. Let the cutter blades do the work. Thin, curled machining chips should fall freely from the lower access window. Note: Back the cutter blades off the work-piece before interrupting the cut. Use compressed air or a small brush to clean the accumulation of chips from the blades and work-piece through the coning operation. The operation is complete when the blades begin to cut the land area at the base of the cone.
Back the cutter blades off the work-piece and loosen the gland to remove the tubing. Inspect the cone for completeness and surface finish.
Important: Clean the machining chips from the blade and from the collet before coning the next tube.

		Replacement Parts
Connection	Catalog Number	Blade	Bushing
1/4" M/P	20HCT4	20BL4	CB4
3/8" M/P	20HCT6	20BL6	CB6
9/16" M/P	20HCT9	20BL9	CB9
3/4" M/P	20HCT12	20BL12	CB12
1" M/P	20HCT16	20BL16	CB16
1/4" H/P	60HCT4	60BL4	CB4
3/8" H/P	60HCT6	60BL6	CB6
9/16" H/P	60HCT9	60BL9	CB9
1" H/P	30HCT16	30BL16	CB16

Reach out to us

Find a Sales Rep Pump & Compressor Selector BuTech Valve Selector Extranet

Hand Tools

Specifications

Hand Tool Instructions

Hand Threading Tool Instructions

Reach out to us

Relief Valves | Haskel

High Pressure Valve Tools | Haskel

High Pressure Valve Power Tools | Haskel

Pipe Equipment | Haskel

Tube OD	Recommended Length
1/4"	1.25" - 1.50" (31.8mm - 38.1mm)
3/8"	1.25" - 1.50" (31.8mm - 38.1mm)
9/16"	1.75" - 2.00" (44.5mm - 50.8mm)
3/4"	3.00 - 3.50" (76.2mm - 88.9mm)
1"	3.00 - 3.50" (76.2mm - 88.9mm)

Connection	Thread Length
1/4" M/P	0.34" (8.6mm)
3/8" M/P	0.44" (11.2mm)
9/16" M/P	0.50" (12.7mm)
3/4" M/P	0.62" (15.7mm)
1" M/P	0.78" (19.8mm)
1/4" H/P	0.56" (14.2mm)
3/8" H/P	0.75" (19.1mm)
9/16" H/P	0.94" (23.9mm)
1" H/P	0.92" (23.2mm)